Inline drip tapes for row crop irrigation
118 products available
118 products available · Page 3 of 5
IRRINEX drip irrigation tape. Diameter: 16mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
Drip tape delivers water precisely at the root zone — eliminating the evaporation and runoff losses that overhead systems accept as a given. Our tape is produced to tight wall-thickness tolerances and emitter spacing consistency, the two variables that most determine whether a field irrigates evenly from header to tail end.
Whether you're running a 2-hectare greenhouse or a 500-hectare field operation, the sizing principles and product specifications remain the same.
Drip tape is a thin-wall polyethylene tube — typically 5–8 mil wall thickness — with molded emitters at fixed intervals along the lay-flat body. Each emitter is a short turbulent-flow labyrinth: water enters under line pressure, slows through the channel, and exits at a rated discharge that stays consistent across a wide operating pressure range.
Installed on the soil surface or buried at shallow depth, the wetted zone stays confined to the crop row. This limits evaporation and suppresses inter-row weed germination — two outcomes no overhead or furrow system can achieve without additional management inputs.
Farmers have been switching to drip tape because it cuts labor, reduces pump load, and delivers measurably better water distribution across long field runs.
The low-pressure, root-zone delivery advantage applies equally from backyard market gardens to large-scale commercial field operations. Our tape is rated for fluctuating pressure, UV exposure, and direct contact with fertilizer solutions.
Three calculations — run in sequence — determine whether your water supply can support your planned layout without zoning.
Fill a 5-gallon bucket at the irrigation connection point and record the fill time in seconds. This gives your available GPM.
Allow one tape line per 12″ of bed width. A 30″ bed requires 2–3 lines depending on soil texture and crop density.
Multiply total footage by the tape's rated flow. If this exceeds your available GPM, zone the system.
| Spacing | Pressure | GPM / 100 ft |
|---|---|---|
| 8″ | 10 psi | 0.6 GPM |
| 12″ | 10 psi | 0.4 GPM |
Manufactured in-house, tested to spec, and shipped to over 60 countries — with the technical depth to support your project from system design through delivery.
Extrusion, emitter molding, and batch testing all on-site. No subcontracting — traceable output, consistent spec.
Wall thickness, emitter spacing, and roll length adjustable to project requirements. Flexible MOQ by product type.
Containerized shipments with full export documentation. 60+ countries supplied, FOB / CIF / CFR available.
System sizing, emitter selection, and filtration requirements reviewed before you order — at no charge.
Need help selecting Drip Tape? Contact IrriNex for samples, specifications, and quotation support.
IRRINEX irrigation pipe or hose. Diameter: 12mm 16mm 20mm; Working Pressure: 0.05-0.1MPa; Wall thickness: 0.18mm~0.6mm. Pipe or hose conveys water between irrigation components. Confirm the actual line type and dimensions before selecting connections or planning an installation.
IRRINEX drip irrigation tape. Diameter: 16mm 20mm 25mm; Thickness: 0.15-0.4mm; Working pressure: 0.5-1bar. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Flow rate: 2L 3L 4L; Size: 16mm/20mm; Thickness: 0.2/0.3/0.4/0.5mm; Dripper spacing: 10/20/30/40cm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Thickness: 0.2-0.6mm; Diameter: 16mm; Flow rate: 1.38-3L/H; Working pressure: 0.5Bar~2Bar. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Length: 1000m/2000m; Working pressure: 1bar; Pipe Diameter: 16mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.3mm; Spacing: 10cm, 15cm, 20cm, 30cm,40cm; Flow: 1-4L/h. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; spacing: 5cm-50cm; Length: 1000m/roll or 2000m/roll; Thickness: 0.15mm-0.6mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Size: 16mm; Thickness: 0.15/0.18/0.2/0.3/0.4/0.5/0.6mm; Spacing: 10/15/20/25/3040/50cm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Diameter: 12mm 16mm 20mm; Thickness: 0.18-1.2mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; spacing: 5cm-50cm; Length: 1000m/roll or 2000m/roll; Thickness: 0.15mm-0.6mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Spacing: 5cm-50cm; Length: 1000m/roll , 1500m/roll, 2000m/roll; Thickness: 0.15-0.6mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.2-0.4mm; Roll length: 1000/2000m. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX irrigation system offering. Diameter: 16 mm; Thickness: 0.2-0.6mm. An irrigation system offering should be configured around the intended site and crop. Listing scope does not establish a complete bill of materials or guarantee area coverage.
IRRINEX drip irrigation tape. Thickness: 0.2mm; Diameter: 16mm; Diameter: 16inch. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.2mm; Diameter: 16inch. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. thickness: 0.2,0.3,0.4mm; spacing: 10cm,15cm,20cm,30cm and customizable; Diameter: 16inch. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16; Diameter: 16mm; Length: 1000m/2000m; Working pressure: 1bar. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; thickness: 0.2mm,0.3mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.2-0.6mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.2-0.6mm. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX drip irrigation tape. Diameter: 16mm; Thickness: 0.2-0.8mm; working pressure: 1 bar (0.1Mpa); flow rate: 1.38--4 L/H. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
IRRINEX irrigation product or planting accessory. Size: Diameter 16mm; Wall thickness: 0.18mm~0.6mm. Select this listing by its exact product identity and documented dimensions or material. The source details should establish the actual component type before a configuration is confirmed.
IRRINEX drip irrigation tape. Diameter: 16mm; Length: 2000m; Working pressure: 1bar; Working Pressure: 0.1-1.0Mpa. Drip tape forms a lateral watering component with a selected outlet arrangement. Diameter, wall thickness and emitter options should be checked as one exact configuration.
